Guide
How to remove hard water stains from glass
An acid, enough time, and a squeegee afterwards.
Short answer
Hard water spots are calcium carbonate left when water dries, and an acid dissolves them. Soak a cloth in white vinegar, lay it on the glass for 10 to 15 minutes, then wipe, rinse and squeegee dry. A citric acid solution of about 53 g per litre works the same way without the smell. Repeat on thick deposits rather than scrubbing hard, and never mix vinegar with bleach.
Why acid works
The white film is mostly calcium carbonate, the same mineral as limescale. Acid reacts with it, turning it into a salt that dissolves in water and a little carbon dioxide, the fizz you see on thick scale. With vinegar:
CaCO3 + 2 CH3COOH → Ca(CH3COO)2 + H2O + CO2
Each gram of scale takes 1.20 g of acetic acid. US vinegar must contain at least 4 g of acetic acid per 100 mL (FDA Compliance Policy Guide 525.825), and white vinegar is usually sold at 5%, so a gram of scale needs about 24 mL of it. That is plenty: the limit is contact time, not quantity.
How much your water leaves behind
When water dries, all of its hardness stays on the glass. The amount is set by your hardness:
| Hardness (gpg) | Residue (mg per litre dried) | 5% vinegar to dissolve it |
|---|---|---|
| 5 | 86 | 2.1 mL |
| 10 | 171 | 4.1 mL |
| 15 | 257 | 6.2 mL |
| 20 | 342 | 8.2 mL |
| 25 | 428 | 10.3 mL |
| 30 | 514 | 12.3 mL |
This is why spots return so much faster in some homes. The median sample in South Dakota is 403 mg/L and in Maine 17 mg/L, so the same splash leaves about 24 times as much mineral on a shower door in South Dakota. At 15 gpg, each litre that dries leaves 257 mg; at 5 gpg, 86 mg.
Vinegar or citric acid
| Acid | Strength | Notes |
|---|---|---|
| White vinegar | 5% acetic acid, used neat | Cheap and everywhere; strong smell |
| Citric acid powder | About 53 g per litre of warm water | Same acid capacity as 5% vinegar, no smell |
Citric acid gives up three hydrogen ions per molecule to acetic acid’s one, which is why 53 g in a litre matches 5% vinegar. Lemon juice is citric acid too, but its strength varies; measured powder is more predictable.
Step by step
- Rinse off loose dirt and soap film with warm water.
- Apply the acid and keep it wet. Spray it on or lay a soaked cloth or paper towel on the glass. On a vertical door, plastic wrap over the cloth stops it drying out.
- Wait 10 to 15 minutes, longer for thick crust.
- Wipe with a non-scratch sponge, working on the spots that remain.
- Rinse with clean water so the dissolved minerals do not dry back on.
- Squeegee or dry with a microfibre cloth.
- Repeat on anything left. Several short rounds beat one round of hard scrubbing.
For a few stubborn specks, the glass industry’s cleaning guidance (IWCA and GANA) allows a razor blade on small spots only: a new blade, on wet glass, scraping in one direction. It is not for routine cleaning or for whole panes.
What not to use
- Bleach with vinegar or any acid. The mix gives off chlorine gas. Washington State Department of Health lists vinegar among the acids never to combine with bleach.
- Acid on marble, limestone or travertine. These stones are calcium carbonate, so the acid that dissolves scale etches them. Mask the stone or wipe spills at once.
- Baking soda as the cleaner. It is alkaline, so it does not dissolve calcium carbonate, and mixed with vinegar it neutralises the acid you need.
- Steel wool and scouring powder, which can scratch glass and remove coatings.
If spots do not shift after several rounds of acid, they may be silica rather than calcium. Watts notes in its specification for salt-free conditioners that silica makes water spots difficult to remove, and acid does not dissolve it.
Keeping spots from coming back
The residue is proportional to the water left to dry, so a squeegee after each shower removes most of it before it forms. Removing the hardness stops it at the source: a salt softener does, but a salt-free conditioner does not, because the minerals stay in the water.